How To Cut The FRP Panels Quickly Before Installing

Fiberglass reinforced plastic (FRP) panel is a kind of wall covering that is endurable and delightful to decorate the walls. To fit on these walls, the FRP panels need to be cut precisely during the FRP installation process.

More...

The configuration of FRP boards specifies the use of special blades to complete the cut. On the one hand, the safety standards need to make on the top authority as the flying debris, cuts and FRP dust could appear in the air.

Equipment you will need to use in the cutting operation

To have a smooth trip, you need to gear up some main tools and other supporting gadgets as follows:

  • The leather gloves
  • A carpenter pencil
  • A particulate respirator
  • The safety glasses
  • A tape measure
  • A chalk line
  • A thin carbide circular saw blade (you could use another blade like a diamond blade or a heavy duty rotary saw)
  • A masonry
  • A utility knife
  • A table
  • A fan
  • A shop coat

soure: buildingmycobra.wordpress.com

Kick off the cutting process

​Step 1: Wear the safety protection

To begin with your task, you should wear the leather gloves, the safety glasses, and one particulate respirator in order to avoid the dust because the FRP pieces could fly through the air.

Step 2: Begin the measurement task

You open the tape measure and put it on the FRP sheets firstly. Then, you take a carpenter pencil to spot the lines that you might want to cut on an edge of the FRP panel.

To have an analogous line on the opposite edge of the FRP boards, you should repeat the marking points on an edge of the panel.

In this time, you take the panel on a table which is solid and sturdy enough to keep the entire length of the FRP tightly.

Soure: www.fiberglassgratingpros.com

Step 3: Use the circular saw to cut the FRP panel

After that, you create a line between two pencil marks and the chalk line to keep the carbide blade of the circular saw, and the circular saw in the right line in order to make the noticeable line over the edge of the table.

After having the marked line, you arrange the blade of the carbide circular saw with the chalk line by pressing the trigger of the circular saw and slowly shove the blade in the FRP sheet.

When shoving the blade across the FRP panel, you still need to align the chalk line and the blade of the carbide circular saw.

Step 4: Finish the cutting process

To finish the process, you need to change the sharp edge of the utility slowly to evade the cutting edge of the FRP.

Moreover, you should take the blade at a 15 - degree angle and hold the utility knife along the cut to take off the burr remaining when cutting the FRP panel.

One thing to keep in mind is that you should not get the blade along the cut as the blade will harm the FRP sheet.

Soure: www.facadesplus.com

After cutting the FRP sheets, you should seal the products to stake off the corrosion of the glass fibers. Some manufacturers could use a comparable resin to evade the state of the corrosion in the glass fibers.

Some safeguard points to remember while cutting the FRP panels

Should

  • Take the safety glasses and a particulate respirator to protect your eyes, your facial skin as well as your nose from the dust.
  • Always wear the gloves, a shop coat, the neck and the sleeves taped to avoid the irritation during the process.
  • Use a fan to help you keep away from the dust.
  • Clean up the cutting area to protect everyone from the dust after closing the process.

Should Not

  • Choose the dark area when cutting the FRP panels.
  • Put the FPR sheet in the surface that is soft and weak.
  • Close the door while cutting the FRP panels.

Conclusion

Cutting the FRP panels is not a daunting task when you know the cutting process accurately and practice the techniques regularly. In addition, you should also follow the safety requirements to prevent all of the accidents and damages could happen at any time. After finishing the cutting process, you could totally install these FRP panels on the walls in your home.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: